Indian Hills Colorado Well and Drilling Guide

How deep are wells around Indian Hills?

How much water do wells make near Indian Hills?

Indian Hills well depth follows the mountain bedrock

Indian Hills wells are commonly drilled into fractured granite, gneiss, or other unnamed fractured-bedrock formations. The median reported depth is 315 feet. The middle half of wells falls between 163 and 505 feet, while 20% are 600 feet or deeper. The deepest recorded well reaches 4,095 feet.

For a buyer, that range is more useful than the median alone. A driller bidding a lot near the middle of the local record may be planning a hole around 315 feet, but access, ridge position, fractures, and the specific parcel can move the finished depth substantially. Only 13% of wells are under 100 feet, so a shallow-well assumption is not a sound construction budget.

Plan around a typical 6 gpm well, not a guarantee

The median reported pump yield near Indian Hills is 6.0 gallons per minute. The middle half produces 3.0 to 9.0 gallons per minute. The largest group, 57%, reports between 5 and 15 gallons per minute; 34% report between 1 and 5 gallons per minute, and 3% report under 1 gallon per minute.

That distribution supports many household uses, but it does not promise a particular parcel will perform the same way. Fractured-bedrock wells can make water through limited fractures, so nearby results are useful evidence rather than a guarantee. Ask for the well construction report, pump test information, storage capacity, and any restrictions attached to the permit. A 1 gpm result deserves a different conversation than a 6.0 gpm result, especially for a larger home or irrigation plans.

Water levels changed across the Indian Hills record

Among the wells reporting static water levels, the median depth to water is 100 feet below the surface, with the middle half between 40 and 176 feet. That is the water level when the well is not being pumped, not the same thing as the depth of the well or the water available during pumping.

The decade series does not show a simple continuing decline. Median depth to water was 40 feet in the 1960s and 1970s, 80 feet in the 1980s, and 150 feet in the 1990s. It was 140 feet in the 2010s and 115 feet in the 2020s. The record suggests deeper water levels than the earliest measurements, followed by some recovery, but reporting is limited to 231 wells and should not replace a parcel-specific evaluation.

Indian Hills permit history shows long-running drilling

Permit activity around Indian Hills spans decades. The records contain 113 permits from the 1950s, 279 from the 1960s, 1,372 from the 1970s, 853 from the 1980s, 1,152 from the 1990s, 601 from the 2000s, 375 from the 2010s, and 181 from the 2020s. The newest permit year is 2025.

The most frequently named drillers in these records are James Drilling Company, associated with Keaton, Michael K., with 487 wells; Aspen Drilling Company Inc, associated with Beery, Leroy J., with 430; and Living Water Systems Inc., associated with Goble, Robert, with 382. These names help locate comparable permit records. They do not establish current availability, pricing, warranty terms, or performance for a new project.

Indian Hills drilling cost depends heavily on depth

Local ground conditions are fractured mountain bedrock, described in the cost model as granite and gneiss. The typical drilling rate is $65 to $100 per foot. At the local median depth of 315 feet, the drilled hole works out to about $20,500 to $31,500.

A usable water system costs more than the drilled hole. Including the pump, pressure tank, trenching, and electrical work, the modeled finished-well range at that depth is about $26,500 to $43,500. Treat this as a planning range, not a firm quote. A lot that requires a deeper hole, difficult access, more trenching, or additional site work can exceed it. Get the bid in writing and confirm what casing, grout, testing, pump equipment, electrical service, and restoration are included.

Check environmental and site risks before closing

Within about 10 miles of Indian Hills, the mapping shows 81 PFAS sampling or contamination sites, 113 historic mine features, and 55 EPA Superfund or cleanup sites. Those mapped sites do not prove that a particular well is contaminated, but they are a reason to review location, groundwater direction, prior land uses, and available test results before buying.

Low yield and dry holes are separate risks in fractured rock. Review neighboring well depths and yields, then have a qualified professional evaluate the proposed location. Septic design, setbacks, driveway access, trench routes, and building placement can affect the project as much as drilling. Confirm the DWR permit allows the intended household use. Exempt household-use wells generally have a 35 gpm pumping limit, and an augmentation plan may be needed in an over-appropriated basin.

Use nearby well records before buying an Indian Hills lot

Start with the exact parcel, then compare permitted wells near Morrison, Idledale, Kittredge, Genesee, Evergreen, and Dakota Ridge only when their geology and elevation are reasonably similar. Look for reported depth, yield, static water level, construction details, and the age of each record. The local median gives a budget anchor, while the 163-to-505-foot middle range shows why one nearby success is not enough.

For a new build, confirm the water-rights and permit requirements before finalizing plans. Have a driller inspect access and propose a realistic depth range, and have the septic designer consider soil, slope, setbacks, and the well location together. If a property already has a well, test the water and verify the permit and construction record rather than relying on a seller’s description.

Well permits by decade near Indian Hills

What a new well costs in Indian Hills, CO

How this is built: the median permitted depth here times the per-foot range for this ground, plus the normal system costs. A lot at the 75th-percentile depth (505 ft) would run roughly $38,825–$62,500. See the full Colorado well cost guide.

Environmental sites mapped within about 10 miles

Counts come from EPA, USGS and state datasets layered on the Colorado Well Finder map. A count is not a verdict on any one well; it tells you what to test for.

Buying land near Indian Hills? Know what it costs to build before you buy the dirt.

A listing photo can't tell you whether a lot is a dream or a money pit. Two parcels near Indian Hills can carry the same asking price while one needs an $80,000 driveway and a $45,000 engineered septic the other doesn't. The well numbers on this page are the start of that answer. A Tri-Lakes Site Feasibility Report is the rest of it: a licensed general contractor, excavator and septic installer reads the parcel the way we would if we were about to build on it, and puts the real cost in writing before your money is committed.

Spend a little to know. Or gamble a lot to guess. Realtors sell the view and inspectors look at houses that already exist. We're the people who'd build it, so we catch what quietly turns a "great deal" into a budget disaster: bad access, buried rock, steep grade, soil that won't pass for a normal septic, water that's a fortune to reach. And if the lot is good, you've already got a builder ready to do the work, driveway to drywall.

• Instant Online Report, $99 — type the address and get a buildability read on the spot: parcel, terrain and slope, soil and septic outlook. Cheap enough to run on every lot you're shopping.
• Desktop Report, $500 — a contractor's from-the-desk feasibility read: Regulation 43 and county code, GIS parcel data, terrain, flood and drainage, soil and septic viability, setbacks and buildable envelope, nearby well depths from our 591,000-well database, the likely driveway route, and a preliminary site-development cost breakdown.
• On-Site Report, $2,000 — everything above, then boots and a drone on the actual ground: house pad and septic zone located, access and winter conditions checked, rock and soil observed in person, a 15 to 20 page written opinion you can hand a lender or seller. Credited toward your project if you build with us.

Under contract, comparing parcels, or a realtor with a rural listing whose buyers keep asking "what will it cost to build here?" This is the due-diligence step almost everyone skips, and the one that saves the most.

Common questions about wells in Indian Hills

Keep researching

More in Jefferson County

All wells in Jefferson County — county-wide depth, yield and cost figures.

Nearby areas