What Holyoke Wells Cost, Produce, and Require

How deep are wells around Holyoke?

How much water do wells make near Holyoke?

Holyoke well depth follows the plains geology

The median reported well depth near Holyoke is 275 feet. The middle half runs from 220 to 300 feet, and the 90th percentile is 320 feet. The deepest well in the records reaches 425 feet. For a drilling bid, that middle range is more useful than the deepest example: a contractor will usually need to price a hole in roughly the local common depth band, then allow for differences between lots.

Depth records show 67% of wells between 100 and 300 feet and 33% between 300 and 600 feet. None are recorded under 100 feet or above 600 feet. Permits name the Ogallala, High Plains Aquifer, and unnamed or fractured-bedrock aquifer. In this plains setting, alluvium and sedimentary rock can produce different drilling conditions from one parcel to the next.

Most Holyoke wells report useful production

Among the 125 local records that report a pump yield, the median is 20.0 gallons per minute. The middle half is 15.0 to 43.0 gallons per minute. Eighty-three percent report more than 15 gallons per minute, 16% report 5 to 15 gallons per minute, and 1% report 1 to 5 gallons per minute. No reported wells are under 1 gallon per minute.

That is a favorable production profile for many household and agricultural uses, but a reported yield is not the same as a guaranteed household supply. Ask for the well completion report, pump information, and any pumping or recovery data. A domestic exempt well is generally subject to a 35 gallon-per-minute pumping limit, and the permitted use still controls what the well may legally serve.

Holyoke water levels show a deeper recent measurement

The median static water level is 178 feet below the surface, with the middle half from 134 to 195 feet. That measurement describes the water level when the well is not being pumped; it is not the same as total well depth or pump setting.

The decade series moves from 124 feet below the surface in the 1960s to 186 feet in the 2010s and 197 feet in the 2020s. The available measurements therefore show a deeper measured water level in the later decades. That pattern is worth checking, but it does not by itself prove a uniform decline across every Holyoke parcel. Have a contractor compare nearby wells, construction dates, aquifer names, and current measurements before relying on the trend.

Holyoke's permit history identifies local drillers

Permits have been issued around Holyoke from the 1950s through the 2020s, with the newest permit year recorded as 2025. The largest decade totals are 81 permits in the 2000s, 73 in the 1990s, 52 in the 1970s, and 52 in the 2010s. Those records show continued well construction and modification, but they do not prove that every older well remains usable.

The most active drillers named in these records are Wellstone Industries Dba Twiss & Wilson Drilling Inc. with 84 records, Wellstone Services, Llc. with 21, and Haggard Drilling Inc. with 17. Treat those names as a starting point for record research, not as a recommendation. Confirm current licensing, insurance, availability, and experience with the specific aquifer and construction conditions on your parcel.

Holyoke drilling cost depends on depth and completion

For Holyoke's alluvium and plains sedimentary rock, the supplied drilling model uses $35 to $55 per foot. At the 275-foot median depth, the drilled hole works out to about $9,600 to $15,100. That is the hole only, not the complete water system.

A finished well with pump, tank, trenching, and electrical is modeled at about $15,600 to $27,100 at the median depth. A bid can move outside that range when the hole is deeper, casing or grout requirements change, access is difficult, or the site needs more electrical and trench work. Get the drilling, casing, development, pump, pressure system, and connection items separated in writing so competing bids cover the same work.

Check water quality, septic separation, and dry-hole risk

Within about ten miles of Holyoke, mapped environmental records include 10 PFAS sampling or contamination sites. There are no historic mine features and no EPA Superfund or cleanup sites in the supplied mapping. That does not establish the quality of water at a particular home. Test an existing well before closing, and test a new well after construction using a panel suited to the property and intended use.

Low reported yield is uncommon in this record, but a new hole can still miss the most productive zone or encounter construction problems. Confirm casing, grout, wellhead protection, pump capacity, and static and pumping levels. Keep the well and septic layout compliant with applicable separation requirements, and verify that the lot has room for the septic system, replacement area, access, and building foundation.

What to do before buying or building near Holyoke

Start with the exact parcel and pull every nearby DWR permit and completion report you can find. Compare depth, aquifer name, yield, static water level, well age, and permitted use with wells in Holyoke, Paoli, and Amherst. Records from Haxtun, Ovid, Sedgwick, and Julesburg can provide broader context, but the closest wells usually deserve the most weight.

For an existing home, make the purchase contingent on a licensed inspection, water-quality testing, pressure and storage checks, and a review of the well permit. For vacant land, budget the complete well system rather than only drilling. Confirm access for a rig, septic feasibility, electrical service, and the legal water use before construction plans are final. A favorable nearby yield helps, but only a site-specific well and permit review answers the real question.

Well permits by decade near Holyoke

What a new well costs in Holyoke, CO

How this is built: the median permitted depth here times the per-foot range for this ground, plus the normal system costs. A lot at the 75th-percentile depth (300 ft) would run roughly $16,500–$28,500. See the full Colorado well cost guide.

Environmental sites mapped within about 10 miles

Counts come from EPA, USGS and state datasets layered on the Colorado Well Finder map. A count is not a verdict on any one well; it tells you what to test for.

Buying land near Holyoke? Know what it costs to build before you buy the dirt.

A listing photo can't tell you whether a lot is a dream or a money pit. Two parcels near Holyoke can carry the same asking price while one needs an $80,000 driveway and a $45,000 engineered septic the other doesn't. The well numbers on this page are the start of that answer. A Tri-Lakes Site Feasibility Report is the rest of it: a licensed general contractor, excavator and septic installer reads the parcel the way we would if we were about to build on it, and puts the real cost in writing before your money is committed.

Spend a little to know. Or gamble a lot to guess. Realtors sell the view and inspectors look at houses that already exist. We're the people who'd build it, so we catch what quietly turns a "great deal" into a budget disaster: bad access, buried rock, steep grade, soil that won't pass for a normal septic, water that's a fortune to reach. And if the lot is good, you've already got a builder ready to do the work, driveway to drywall.

• Instant Online Report, $99 — type the address and get a buildability read on the spot: parcel, terrain and slope, soil and septic outlook. Cheap enough to run on every lot you're shopping.
• Desktop Report, $500 — a contractor's from-the-desk feasibility read: Regulation 43 and county code, GIS parcel data, terrain, flood and drainage, soil and septic viability, setbacks and buildable envelope, nearby well depths from our 591,000-well database, the likely driveway route, and a preliminary site-development cost breakdown.
• On-Site Report, $2,000 — everything above, then boots and a drone on the actual ground: house pad and septic zone located, access and winter conditions checked, rock and soil observed in person, a 15 to 20 page written opinion you can hand a lender or seller. Credited toward your project if you build with us.

Under contract, comparing parcels, or a realtor with a rural listing whose buyers keep asking "what will it cost to build here?" This is the due-diligence step almost everyone skips, and the one that saves the most.

Common questions about wells in Holyoke

Keep researching

More in Phillips County

All wells in Phillips County — county-wide depth, yield and cost figures.

Nearby areas